Did your roofer mention installing a cant strip on your flat roof, and now you’re wondering if it’s actually necessary or just another extra charge? Are you worried that skipping a small component like this could lead to leaks or expensive damage later on, especially with Seattle’s constant rain?
Flat roofs in Seattle face unique challenges. A cant strip isn’t required for every type of membrane, but is needed when you install torch down. It helps prevent cracks that can cause tens of thousands of dollars in damage.
At RoofSmart, we’ve installed and repaired hundreds of flat roofs all over the Seattle area. We are familiar with the rules and requirements for installing each material and pay meticulous attention to detail so that your roof comes out great every time.
In this article, we’ll explain what a cant strip does, when it’s required on a flat roof, and whether it’s something your Seattle roof actually needs.
| Roofing Material | Is a Cant Strip Required? | Why or Why Not | Risk Without One |
|---|---|---|---|
| Torch Down (Modified Bitumen) | ✅ Yes (Required) | Thick, inflexible membrane can’t bend at 90° angles | Cracking, tearing, leaks |
| PVC Roofing | ❌ No | Flexible membrane can handle corners | Minimal risk |
| TPO Roofing | ❌ No | Flexible and designed for corner transitions | Minimal risk |
| EPDM Rubber | ❌ Not typically | Flexible material adapts to edges | Low risk |
| Any Flat Roof (Optional Upgrade) | ⚠️ Optional | Adds slope and improves drainage | No downside, but added cost |
A cant strip is a triangular fitting that is installed in the corner of your flat roof to prevent a sharp bend in the membrane that can lead to tearing. This is a concern with torch down because the membrane is too thick to make that 90-degree bend.
Here’s an example of what a cant strip looks like and how it’s installed on the roof:
Image from Blue Ridge Fiberboard
As you can see, it creates a smooth, angled plane rather than fitting the membrane to the shape of the corner or edge. Cant strips run along the entire perimeter of your roof.
You're supposed to adhere the membrane to a parapet wall, and you can't really do that if you're trying to get this thick torch down to go at a 90- degree angle. It's never going to bond in the corner, whereas PVC actually will.
As it gets cold, the corners of your flat roof can become stress points. And a lot of times, that's where there's building movement: the wall might move, or the roof deck might move at the corner. Torch down will tear with this kind of thermal expansion and contraction.
The last thing you want on a flat roof is a tear in the membrane because it’s definitely going to turn into a leak, especially with all the rain that we get in Seattle.
Flat roof leaks are hard to spot because there isn’t an attic to check. This means that the leak can happen for a long time before you notice, and end up causing significant rot and deterioration within your roof. We see extensive damage from flat roof leaks all the time in the Seattle area.
Cant strips are typically made of wood because it’s an affordable option. They can also be made of other materials, like EPS foam, metal, or even modified bitumen (which is another term for torch down). Here are some examples from Asiri Designs:
A cant strip is recommended for all roof assemblies, but it's only required for torch down because it is at risk of cracking or tearing without one.
Torch down is a thick fiberglass mat, which is not very flexible. The thicker the membrane, the more important it is to have a cant strip.
However, other flat roof membranes, like PVC and TPO, are much more flexible and can handle small shifts the building might make. These products can be installed tight to the corners without concern of tearing or cracking.
You can choose to have them installed on your roof if you’re not using torch down, but it’s not necessary. Roofers usually skip this step on PVC or TPO roofs.
Although installing a cant strip can add a little extra cost to your project, it’s a pretty minimal amount because the wood is fairly cheap (It's like a dollar a foot or less). Aside from that, there are really only benefits:
It's never a bad idea to do a can't strip. It never hurts your roof, but it’s only needed on a torch down roof. It’s completely fine to skip this step if you have TPO or PVC.
Aside from the other benefits, you might want a cant strip because you prefer the aesthetic of a slope rather than a tight corner. This is an easy preference to accommodate.
If you really want cant strips on your roof, talk to your roofer to see what they think. They can help you decide if it’s a good move or just an unnecessary extra step.
As you’ve seen, even a small component like a cant strip can play an important role in how well a flat roof performs, especially if you’re installing a torch down membrane that needs protection from stress at corners and edges. Details like this help prevent tears, improve drainage, and make maintenance easier over the life of your roof.
But they also highlight an important reality about flat roofing projects: the final cost isn’t just about the membrane you choose. The price of a flat roof installation depends on the entire system, which includes roof material, insulation, drainage details, labor, and smaller components like cant strips that help the roof function properly.
If you're planning a flat roof project in the Seattle area, understanding the full scope of what goes into the installation can help you budget realistically and compare contractor estimates more confidently.
Read our article “How Much Does It Cost to Install a Flat Roof in Seattle?” to get a breakdown of the real factors that influence flat roof pricing so you can better understand what you’re paying for and why.
If you’re deciding whether a cant strip is necessary for your flat roof, these common questions will help clarify when it’s required and when it’s optional.
No, not all flat roofs require a cant strip.
Cant strips are only required for torch down roofing systems because the material is thick and prone to cracking at sharp angles. Other materials like PVC and TPO are flexible enough to function without one.
Without a cant strip, torch down roofing can:
Because these weak points are common failure areas, skipping a cant strip can lead to costly repairs.
Yes, especially for torch down roofs.
Cant strips are relatively inexpensive but help prevent:
For other roof types, they are optional but can still improve drainage and maintenance.
In some cases, yes. But it depends on the condition of your current roof.
Cant strips are typically installed during a full roof replacement. Retrofitting one into an existing system may require partial tear-off and additional labor.
Cant strips also:
Even when not required, they can enhance overall roof performance.